LUBEGARD AUTOMATIC TRANSMISSION FLUID (ATF) PROTECTANT is for use in all automatic transmissions and manuals requiring an ATF, including heavy duty transmissions, such as Allison. Use with all synthetic or mineral based DEXRON, MERCON & OEM (Original Equipment Manufacturers) ATFâ€™s (except Ford Type F ATF & CVT applications). Lubegard controls heat and is especially effective in todayâ€™s hotter running front wheel drive vehicles. It contains LXE (Liquid Wax Ester) Technology and their derivatives, base oils and conventional additives. Lubegard is designed to raise the thermal and oxidative stability level of automatic transmission fluids, so when it operates at elevated temperatures, it does not thin out and pyrolize, burn or react with oxygen and form deposits. The use of LUBEGARD ATF Protectant will not cause clutch friction upset or slippage. DIRECTIONS FOR USE: For normal applications, add 1 oz. (29.6 mL) per quart (Liter) of ATF to the total transmission capacity (including torque converter) with motor idling in park. Do not overfill.
Dr. Tranny Kooler Kleen Flush Cleaner with Universal Tip is used, repackaged and designated by multiple car manufacturers and the largest transmission rebuilders. This is because it is the only mineral based transmission line flush. There is absolutely no water used in the formulation. Caustic water-based flushes leave behind a film of detergents and dispersants, water and soapy residue that will become part of the new ATF when the transmission is re-installed which can cause shudder and damage to clutch plates. Lubegard Kooler Kleen ensures the new ATF stays free of water and that the transmission is installed to last. Lubegard Kooler Kleen is a three-in-one product. Transmission rebuilders use it as a line flush cleaner, a wire harness cleaner, and a dielectric protectant. For use as a line flush cleaner: simply attach the connector to the transmission feed line; next, attach the hose to a transmission return line to collect flush and residue in a waste container; hold the can upright and actuate; flush until clear. For best results use the entire content of can per installation. Then turn the can upside down and continue cleaning with air only. For wire harness cleaner: cut off the hose to appropriate length to direct the stream. Spray over dirty depowered 6-12 volt electrical components. For a dielectric protectant: allow cleaned components to dry before repowering.
Lubegard Platinum Universal ATF Flush and Protect Pack features the safest, most gentle transmission flush available. Other transmission flushes contain harmful solvents that can actually dissolve seals and gaskets. The Lubegard transmission flush is designed to gently flush away varnish, sludge, and other by-products and prepare your transmission for fresh fluid. The directions for use with the flush machine include following the manufacturers directions. The directions for use without the flush machine include adding one bottle of Lubegard automatic transmission flush to the transmission fluid. With the car on lift (or wheels above the ground) start the engine; circulate for 5 minutes cycling Lubegard automatic transmission flush through all gears. Then drain completely and refill with Dexron/Mercon ATF and one bottle of Lubegard platinum universal ATF protectant. The Lubegard platinum universal ATF protectant is uniquely formulated using the patented synthetic LXE (liquid wax ester) technology and new synthetic synergol TMS technology. Together, these technologies provide the most advanced and complete transmission fluid performance service additive ever invented. It is used to convert regular Dexron/Mercon ATF into OEM types and perform like MERCON V ATF, highly friction modified ATFs, such as: Honda Genuine ATF, Toyota Type T, Toyota Type TII, Toyota Type TIV, Mopar ATF + 3 (7176), Mopar ATF +4 (9602), and all other highly friction modified ATFs.
Lubegard ATF Flush and Protect Pack features the safest, most gentle transmission flush available. Other transmission flushes contain harmful solvents that can actually dissolve seals and gaskets. Lubegard transmission flush is designed to gently flush away varnish, sludge, and other by-products and prepare your transmission for fresh fluid. The directions for use with flush machine: follow the manufacturers directions. The directions for use without flush machine: add one bottle of Lubegard automatic transmission flush to the transmission fluid. With the car on lift (or wheels above the ground) start the engine; circulate for 5 minutes cycling Lubegard automatic transmission flush through all gears. The drain completely. Refill with ATF. After the flush is complete, add Lubegard ATF protectant for unsurpassed protection.
Brand: ATP Automotive
Engines, transmissions, and power steering systems slowly accumulate sludge, varnish, and contaminants over time. ATP AT-218 Multi Service Flush is designed to clean all these systems enhancing overall performance and long life.